电气参数 Electrical parameters
|
项 目Item |
参 数Parameter |
项 目Item |
参 数Parameter |
|
额定电流 Rate current |
50mA |
额定电压 Rate voltage |
DC 12V |
|
接触电阻 Contact resistance |
≤100mΩ |
绝缘电阻 Insulated resistance |
≥100MΩ |
|
介电强度 Dielectric strength |
250VAC/1min |
操作力 Operating force |
250±40gf(可选) |
|
产品寿命 Service Life |
30,000-2,000,000Times(可选) |
行程 Travel： |
0.2±0.1mm |
|
盐雾试验Salt Mist (铁材质不做盐雾要求) |
Time: 24h/ 48h/ 72h /96h |
自动焊接温度 soldering temperature |
260℃±5℃ max |
|
手工焊接 Hand soldering |
焊锡温度：≤350℃ Soldering temperature:350℃ 3s Max . |
焊接次数 soldering times |
一次，低温锡可以满足两次 1 times Low-temperature solder can meet two times. |
其他事项
1、请不要从轻触式开关上面浸入助焊剂。
2、关于密闭型以外的型号，对异物的侵入，请充分注意。
3、进行焊接过程中，不可以用溶剂或类似品清洗开关。
4、防止助焊剂从开关的外部渗入。
5、给端子进行焊接时，如果在端子上施加负荷，因条件不同会有松动，变形及电气特性劣化的可能。
6、进行两次焊接时，请在第一次焊接部分回复到常温之后再进行。连续加热可能使外围部变形，端子的松动， 脱落及电气特性降低。
7、关于焊接的条件设定，需要确认实际批量生产条件。
8、本产品以直流的电阻负荷为前提设计制造的。作为其他的负荷【 感应性负荷（L），电容性负荷（C）】使用 时，请另行联系。
9、此开关请用于直接由人操作按开关的结构。请不要用于机械性的检测功能。
10、开关操作时，如果实施规定以上的负荷，开关将有被损坏的可能。请注意不要在开关上施加规定以上的力。
11、请避免从横侧按操作部的用法。
12、如果使用开关的整机的周围材料产生腐蚀性气体，将有可能造成接触不良等现象，所以请事先进行充分的确 认。
13、保管方法
13.1、产品以交货时的状态在常温，常湿，不受直射阳光照射，不产生腐蚀性气体的地方保管，自交货起3 个月以内为限度，请尽可能早点使用。
13.2、开封后为了用聚乙烯袋与外气隔断，请在与上述同样的环境中进行保管，并尽快使用。
13.3、请不要过分的堆积。
13.4、请不要在按断了开关操作部的状态下进行保存。
8.Others:
1. Only the terminals of touch switch can be immersed into the chemical assistant for soldering, other places no.
2. For some models which is belong to not closed housing design, Please pay more attention to unidentified object intrusion.
3. During soldering operation don't use solvent and others to clean.
4. Prevent the assistant solvent seeping into the switch from outside.
5. Please pay more attention when soldering the connectors,if the negative electricity is imposed what maybe causes terminal loosen,distorted.
6. After the temperature is backed to normal then the second time soldering can be Proceeded, under long-time temperature what can cause the product distorted,terminal loosen and fall off, even damage electricity parameters.
7. About soldering conditions setting,it is necessary to confirm mass production conditions.
8. The product is designed and manufactured based on the condition of DC resistant load,And for others loads[inductive load(L),capacitive load(C)] please contact us.
9. The switch structure is designed for manual operation directly, please don't use mechanical devices to test the functions.
10. In operation if the force is out of specification the switch maybe will be damaged, please operate according to the force specification.
11. Avoid pressing the button from side part.
12. Please double confirm in advance if some rotten gas smelt from around the switch what will maybe cause poor connect.
13. Storage conditions:
13.1) Keep them in normal temperature and humidity,no shine directly, keep from corrosive gas. Storage time limitation is 3months, please use up as soon as possible.
13.2) After open it then please keep it in plastic bag from natural environment. please use up as soon as possible.
13.3) Please don't stack too much.
13.4) Please don't store them after broken.
